Extractive Midas® transmitters (universal) operate with sensor cartridges, for use as a local gas detector. Sensor Cartridges must be ordered separately.
Units are powered by 24VDC or via. Power over Ethernet PoE. Transmitters provides 0-22mA analog and Modbus/TCP Ethernet as standard outputs. Integral relays for A1, A2 and fault are included, and may be wired normally open or normally closed, latched or unlatched.
Transmitters include Manual, Quick Start Guide and (1) PG16 gland fitting for power in and relays out, 1/4" O.D.x 1/8" I.D. Sample Inlet tubing (10') [3m], 1/4" O.D x 3/16" I.D. Exhaust tubing (10') [3m], and a sample line tubing duct adapter (1283K1090). Order a sensor cartridge separately for each transmitter.
Order the following parts for a complete Midas® System:
1. Midas® or Midas® transmitter and cartridge kit
2. Sensor cell (if combo kit not purchased)
3. Sample and exhaust tubing
4. End of line filters
Transmitter Modules:
| Midas® Extractive Transmitter for Universal Gas Detection |
| (sensor cartridge must be ordered separately) |
|
Part No: MIDAS-T-004 MIDAS Extractive Transmitter (Generation 2) |
| Pyrolyzer Module for NF3 Gas Detection |
| (order separate transmitter unit) |
| Part No: MIDAS-T-00P MIDAS Pyrolyzer Module |
| Pyrolyzer Midas® transmitters provide detection of NF3 specifically. Unit includes a snap on pyrolyzer module that operates with any Universal Midas® Extractive Transmitter (order separately) and (1) Freon in line filter. Units are powered via direct connection to transmitter unit. Pyrolyzer includes Pyrolyzer Quick Start Guide and installation screws. Order the NF3 cartridge (MIDAS-S-HFX) separately. Order the ventilated top cover (MIDAS-A-103 or MIDAS-A-103G) separately. |
| High Temperature Pyrolyzer Module for Perfluoro Compounds (PFC) Gas Detection |
| Part No: MIDAS-T-NP1 MIDAS High Temperature Pyrolyzer Module |
| (order separate transmitter unit) |
| Higher Temperature Pyrolyzer MIDAS® transmitters provide detection of NF3, Hexafluorobutadiene (C4F6), Methyl Fluoride (CH3F) and Octofluorocyclopentene (C5F8). Unit includes a snap on pyrolyzer module that operates with any Universal MIDAS® Extractive Transmitter (order separately). Units are powered via direct connection to transmitter unit. Consult Honeywell Analytics for additional gases detectable with this option. Pyrolyzer includes Pyrolyzer Quick Start Guide and installation screws. Order the PFC cartridge (MIDAS-S-XCF or MIDAS-E-XCF) separately. Order the ventilated top cover (MIDAS-A-103 or MIDAS-A-103G) separately. |
| LonWorks Module for Midas® Transmitter Connection |
| Part No: MIDAS-T-LON MIDAS LonWorks Interface Module |
| Optional LonWorks interface module that mounts to and connects with any single, universal Midas® extractive transmitter with or without Pyrolyzer (order these separately) to provide bi-directional LonWorks connectivity; remote reset and remote control of the onboard relays. Unit is 24V DC powered and provides power and communications directly to the attached Midas® transmitter using special ethernet cross over cable (supplied). Includes Quick Start Guide and mounting bracket to the Midas® transmitter; rear panel installation screws are not supplied. |
| Quad LonWorks Module for External Transmitter Connection |
| Part No: MIDAS-A-035 MIDAS Quad LonWorks Module |
| Optional Modbus/TCP to LonWorks converter gateway that can connect up to 4 Midas® transmitters (with or without pyrolyzers) to a LonWorks network. Requires separate 24V DC power supply and ethernet connector cables. Suitable for DIN rail mounting. Consult Honeywell Analytics for full technical details. Access to LonMaker programming is required (not included). |
